“I would highly recommend Floor Monkeys!”
Sanded & refinished Douglas Fir floors from 1958 & gave them new life! Fast, efficient, skilled & professional! I would highly recommend Floor Monkeys! 🐒🐒🐒

Floor Refinishing Services
Hardwood floor refinishing for original oak and newer wood floors across Sacramento and the Bay Area, sanded flat, stained evenly and sealed to last.
Sand and finish runs $9 to $11 per sq ft, with a $2,000 minimum. See full refinishing pricing →
Types of Floor Refinishing
We sand the floor down to bare wood, fix what we find, then stain and seal it. Scratches, gray traffic lanes and old color all go away.
A light buff and fresh topcoat for floors that are dull but not worn through. Faster than a full sand, and it keeps more wood on the boards.
Go from orange oak to natural, gray, smoked or dark. We lay test patches on your floor so you pick the color in your own light.
Many older homes hide original oak under carpet. We pull the carpet, pull the staples and bring that floor back.
Treads, nosing and landings sanded by hand and finished to match the floor at the top and bottom of the stairs.
Damaged boards are replaced and gaps filled before sanding, so the repairs disappear into the new finish.
Ready for floors you'll show off?
Free in-home estimate. Written quote. No pressure.
Why Floor Monkeys

| What you get | Floor Monkeys | Typical installers |
|---|---|---|
| License number shown and checkable | ||
| Crew shows up when we say | ||
| Job site cleaned every day | ||
| Moisture test before every wood install | ||
| We move your furniture and move it back | ||
| 1-year workmanship warranty in writing | ||
| Owner personally checks every job |



Floor Refinishing Projects



























Why Floor Monkeys
“The work beneath your floor matters just as much as the surface you see.”
The Step You Never See
Step 6 of 6
The last clear coat leaves a soft satin sheen and protects the wood for years of daily wear.
Stain shows everything. Any scratch, chatter mark or swirl the sander leaves behind soaks up more stain than the wood around it and shows as a dark line or circle. Most bad refinishing jobs fail at this step, not at the stain.
A good refinish starts with a coarse pass to take off the old finish and level the boards. Older oak floors in Sacramento's pre-war neighborhoods have often been sanded before and can be cupped or uneven, so the first passes go at an angle to flatten them. Then each pass uses a finer grit to erase the scratches from the one before. The edges, corners and areas around vents get the same care with smaller sanders and by hand.
A good refinish starts with a coarse pass to take off the old finish and level the boards. Older oak floors in Sacramento's pre-war neighborhoods have often been sanded before and can be cupped or uneven, so the first passes go at an angle to flatten them. Then each pass uses a finer grit to erase the scratches from the one before. The edges, corners and areas around vents get the same care with smaller sanders and by hand.
Before stain, the floor is vacuumed and wiped clean, then checked in low raking light so any marks show up while they can still be fixed. Only a flat, clean floor gets stain.
Worn old finish. Scratches and dull spots sit in the old finish on top of the wood.
Sanded to bare wood. The sander takes the floor down past the old finish.
Stain. Stain soaks into the grain. It is color, not a new layer.
First clear coat. Thin clear coats build up the protection.
Second clear coat. Each coat adds to the sheen.
Third coat, satin. The last coat leaves a satin sheen on the wood.
Floor Refinishing Process
We visit, measure and check your subfloor and current floors.
You get the scope, materials and schedule in writing.
We lock your dates and order your flooring.
We protect your home and get the subfloor flat and ready.
The crew installs or refinishes and cleans up every day.
We walk the floor with you and fix anything you spot.
Floor Refinishing Cost
Floor Refinishing Questions
Solid hardwood can usually be sanded and refinished many times over its life. Engineered floors depend on the wear-layer thickness. We check how much wood is left at your estimate.
Most full refinishing jobs take a few days, plus time for the finish to cure before furniture goes back. Your written quote includes the schedule and dry times for your finish.
Yes. A full sand takes the floor back to bare wood, so you can go lighter, darker or natural. We put test patches down so you can choose on your own floor.
Many people stay in another part of the house, but you will need to stay off the floors during finishing and curing. We plan the work in sections when we can.
If the finish is dull but the wood is not worn through or deeply scratched, a screen and recoat can bring it back. If you see bare or gray wood, you need a full sand.
Service Areas
Sanded & refinished Douglas Fir floors from 1958 & gave them new life! Fast, efficient, skilled & professional! I would highly recommend Floor Monkeys! 🐒🐒🐒
⭐⭐⭐⭐⭐ I cannot recommend Kirill and crew from Floor Monkeys highly enough! From start to finish, they were professional, efficient, and truly cared about doing the job right. When the flooring supplier sold me the wrong product, the crew immediately went to pick up the correct materials without hesitation. They moved all of my furniture, leveled the subfloor, installed beautiful new flooring in both of my bedrooms, and then carefully put everything back exactly where it belonged. Their attention to detail, work ethic, and commitment to customer satisfaction were outstanding. It’s rare to find a company that is this ethical, dependable, and professional. The quality of their work exceeded my expectations, and I couldn’t be happier with the results. If you’re looking for a flooring company you can trust, I wholeheartedly recommend Four Monkeys. They earned every one of these five stars!
Kirill, owner of Floor Monkeys, went well-above anything I expected. We met several times, he tested our hardwood floor, made recommendations on how our once beautiful (and not so old) flooring could be brought back to life. The results were amazing! I was so impressed with the time, care, trust, and level of professionalism I experienced from beginning to end. I would recommend Floor Monkeys to anyone who is in need of the best in the industry...

Ready for floors you'll show off?
Free in-home estimate. Written quote. No pressure.
Floor sanding and refinishing takes worn hardwood back to bare wood and builds a new finish on top. The job runs in order: prep and repair, sanding in passes, cleaning, stain if you want color, then several coats of finish with drying time between each one.
Prep means moving furniture, covering doorways and vents, setting nails that stick up and replacing broken boards. We also pull any staples or tack strip left from old carpet so the sander does not catch them.
Prep means moving furniture, covering doorways and vents, setting nails that stick up and replacing broken boards. We also pull any staples or tack strip left from old carpet so the sander does not catch them.
Sanding is where the floor gets its shape back. A big drum or belt sander does the open areas, an edger does the walls, and corners get scraped and hand sanded. Each pass uses finer paper than the last, so the scratches get smaller until they are gone.
Refinishing original oak floors is some of the most satisfying work we do. Many homes in East Sacramento, Land Park, Curtis Park and older Bay Area neighborhoods still have the oak strip floors they were built with, often hiding under carpet.
Older oak can be thin after past sandings, so we check how much wood is left above the tongue before we start. We sand only as much as the floor needs. Gaps between old boards can be filled, and boards damaged by pets or water can be swapped with matching oak.
Older oak can be thin after past sandings, so we check how much wood is left above the tongue before we start. We sand only as much as the floor needs. Gaps between old boards can be filled, and boards damaged by pets or water can be swapped with matching oak.
Old oak often has a warm color that new oak cannot copy. Many owners choose a natural finish to keep it. Others want to tone down the orange with a light stain. Test patches on your own floor make that choice easy.

Hardwood floor restoration goes past a normal refinish when boards are cracked, stained black by water or pets, or pulled loose. Those boards get cut out and replaced before sanding, so the whole floor is finished as one surface.
Black stains from pet accidents or plant pots usually go deep into the wood and do not sand out. Replacing those boards is the only real fix. We weave the new boards in with the old ones so the repair does not show as a square patch.
Black stains from pet accidents or plant pots usually go deep into the wood and do not sand out. Replacing those boards is the only real fix. We weave the new boards in with the old ones so the repair does not show as a square patch.
Squeaks and loose boards can be fixed during a restoration too, while the floor is bare. We can face-nail or screw from below when we have crawlspace access, then sand the area flat with the rest of the floor.
A screen and recoat scuffs the top finish and adds a fresh coat. A full refinish sands to bare wood. If your floor is dull but not scratched into the wood, screening is enough. If the wood is gray, scratched deep or worn through, you need a full sand.
Screening is faster, makes far less dust and keeps the wood thickness you have. It works well every few years in busy homes, before traffic lanes wear through to bare wood. It will not change the color or remove deep scratches.
Screening is faster, makes far less dust and keeps the wood thickness you have. It works well every few years in busy homes, before traffic lanes wear through to bare wood. It will not change the color or remove deep scratches.
One catch: floors that have been waxed or cleaned with some polish products may not take a new coat. We check for that at your estimate before we recommend a screen and recoat.
Floor sanding and refinishing takes worn hardwood back to bare wood and builds a new finish on top.
To restain hardwood floors, we sand to bare wood, open the grain so it takes color evenly, then apply the stain by hand and wipe off the extra. Before the full floor, you approve the color from test patches on your own boards.
Different woods take stain differently. Red oak shows pink tones under gray stains. White oak takes grays and browns cleanly. Maple can blotch with dark colors. We tell you how your species will react before you fall in love with a color on a sample board.
Different woods take stain differently. Red oak shows pink tones under gray stains. White oak takes grays and browns cleanly. Maple can blotch with dark colors. We tell you how your species will react before you fall in love with a color on a sample board.
After the stain dries, we seal it with your choice of finish and sheen. Matte and satin hide scratches and dust better than gloss, which is why most homeowners pick them.
Hardwood floor refinishing cost depends on square footage, the condition of the floor, the stain and finish you choose and how many repairs are needed. We give you a written quote after seeing the floor, so there are no surprises once we start.
When you search for hardwood floor refinishing near me, ask how the company handles dust, how many finish coats they apply and how long each needs to dry. Ask to see the license number. Floor Monkeys holds California license #1090151.
When you search for hardwood floor refinishing near me, ask how the company handles dust, how many finish coats they apply and how long each needs to dry. Ask to see the license number. Floor Monkeys holds California license #1090151.
We also tell you when not to refinish. If a floor is too thin to sand again, we say so and talk through options like board replacement or a new floor.
A refinished floor stays looking new with felt pads, outdoor mats, a soft vacuum and a wood floor cleaner. Wait until the finish has fully cured before rugs go down or furniture slides back, since fresh finish marks easily in the first days.
Most finishes feel dry within hours but take longer to fully harden. We give you a simple schedule: when you can walk in socks, when furniture can go back and when rugs are safe. Following it protects the work you paid for.
Most finishes feel dry within hours but take longer to fully harden. We give you a simple schedule: when you can walk in socks, when furniture can go back and when rugs are safe. Following it protects the work you paid for.
Plan a screen and recoat when traffic areas start to look dull, before they wear to bare wood. That small step keeps the floor from needing another full sand for many years.
Preparing for hardwood floor refinishing means identifying stains, loose boards and previous repairs before sanding starts. Samples on the existing floor and the finish instructions help establish both the repair scope and how the rooms can return to regular use.
Point out dark marks, loose boards and places where earlier repairs changed the wood. These details affect what can be blended and what may need replacement. Compare stain samples on the actual floor rather than only on a display board. Discuss the finish instructions for walking, furniture and rugs so the plan covers both the work and the return to normal use.
Point out dark marks, loose boards and places where earlier repairs changed the wood. These details affect what can be blended and what may need replacement. Compare stain samples on the actual floor rather than only on a display board. Discuss the finish instructions for walking, furniture and rugs so the plan covers both the work and the return to normal use.
More Wood Services

Solid oak, white oak and wide-plank floors installed over a checked, flat subfloor. We acclimate the wood first so it stays tight through Valley summers.
Hardwood Installation
Real wood on a stable core, made for the slab foundations under most newer Sacramento homes. Glued, floated or nailed, depending on what your floor needs.
Engineered Hardwood
We turn carpeted stairs into wood, replace worn treads and refinish old ones. The nosing is matched to your floor so the stairs look built in.
Stairs
Damaged boards, squeaks and gaps fixed without tearing out the whole floor. We weave in new boards and blend the finish so the repair disappears.
Floor Repair